Welcome to the Off Road Podcast!! I am your host Greg Bakken and joining me is my co host Jeff Bakken...This is the podcast for all things offroad. Whether you're looking for Sunday jaunts on some fire roads or hard core rock crawling, we will cover it all. Episode 13!!!
What's up Jeff?
Hi Jeff & Greg,
Thanks for a great show! I've been enjoying it big time, especially the episodes about winches and axles. As I type this, I'm downloading the latest episode about Auto vs Manual and I can't wait to listen! I always have had manual transmissions and haven't been persuaded by all the lectures I've had over the years on how autos are better off road.
I think it might be interesting to devote an episode to discussing welding on the trail. In years past I wheeled a Land Rover and mounted a second alternator, that I liberated from and old Buick, under the Land Rover hood and turned that into a welder. Now-a-days I carry a Cobra 2575 Watt inverter from Amazon.com and a 90 Amp wire feed welder from Harbor freight. With these I can do some mad welding on the trail and the total cost was just over $200 (not including helmet and rods).
This past weekend I wheeled my '04 Jeep Liberty on The Rubicon from Loon Lake to Buck Island Lake on Friday afternoon, and back out to Loon on Saturday. I was with a longtime friend of mine who drives a nice '07 Wrangler Rubicon LJ and he took a picture of me somewhere along the granite slab not too far past The Gatekeeper. The pic is attached.
Please keep up the great work and I'll be listening,
I just listened to the most recent podcast and you said you now have facebook. I looked for it(the off road podcast) and I can't find it.
Also, you guys mentioned on an earlier podcast on-board welders. I didn't know if you guys wanted to go into some depth about options like Ready Welder, modifying an alternator to weld, or straight off of batteries.
I'm also looking into an on-board air system for filling tires and maybe some light tool work. Any thoughts on Viair, ARB, Warn Powerplant, etc?
Keep the great podcasts coming.
Smittybilt Air Compressors 2781
Here is the follow-up for my warrantee experience with Chrysler.
First to answer your questions during the podcast. I had done no other modifications to my truck other than the 6” Lift Kit and 35” tires. No Power chip or anything.
The warrantee was reviewed again by Chrysler (the factory powertrain department) and once again rejected on the basis of the lift kit.
I talked with the Service Manager on what the dealership would do to make this right for me and he referred me to the Dealership General Manager who decided that the dealership would replace the transmission for me at no cost to me.
At this point I had really lost faith in this truck and asked if he would work me a good deal to trade in my truck for another new one and he agreed to this, going so far as to not deduct anything off my trade in price for the transmission since he had agreed to replace it for me.
So they got me into a new truck at a price I am very happy with. I went ahead and went back to a Ram 2500 HD since I have had such good luck with them in the past. I have had 4 2500’s prior to the 3500. I think I will wait a while before I consider a lift kit again just to be sure that all is well with this truck.
One thing that did upset me during all this is that fact that I had purchased an extended warrantee with the 3500 and when I asked the Service Manager if it would cover the transmission replacement he stated that it would not because the factory warrantee was still in effect, I later found out that it would have but since I have replaced the truck I will not pursue it further.
I hope this help you with any decisions you will make on changes to your vehicles, or at least prompts you to ask questions of the dealership before you decide what to do with them. Most importantly get anything a dealer representative tells you in writing.
Keep up the great podcast and tread lightly out there.
Instead of swapping my entire rear axle for a stronger one, will getting heavy duty axle shafts be enough strength to go up a couple wheel sizes? I have a Geo Tracker and Calmini offers some heavy duty axle shafts. It seems like a much cheaper alternative to an entire axle swap. I would like to run 32s or 33s.
2)Having said that, I still have IFS. Calmini does not offer heavy duty axles shafts for IFS. Would the IFS stand up to 32s or 33s, as is?
I'm a new listener and so far I love the podcast.
Hey guys love the show, find it very informative. I'm hoping you can give me your opinion on some gearing ratios. I have 82 Jeep CJ7 running on 32's with the stock AMC20/Dana30 w/ 2.73's. As you can tell I need a gearing change. The jeep is used mainly for hunting, no extreme wheeling, just logging/fire roads, some street use. I am thinking 3.73's would do the trick or do you think I should go up to 4.10's.
If I decided to do a diff swap, what should I look for? Can you recommend some donor vehicles.
Thanks in advance, looking forward to next show.
JEEP AXLE SWAPS
Send us your questions and comments!!!
Main Topic: King Fire
California’s gigantic King wildfire keeps growing amid warnings of ‘extreme fire behavior’
89,500 acres (or about 139 square miles)
7,300 firefighting personnel