ARP 086 - Accurizing the MSR

arp086-Dimetarget-300x225.jpg

Welcome to Episode #086 of the AR15 Podcast. I’m your host Reed Snyder and with me today is my co-host, Anthony Hardy.  This is the podcast about your favorite black rifle!  This show is for you; whether you're building your first AR or you’ve been building ARs for years. There is something we can all do to take our black rifle to the next level. Brownells helps make this show possible.

Don’t forget that Brownells, with their 100% lifetime satisfaction guarantee, is there for you anytime you have a problem, like when you can’t remove the taper pins from your new barrel to slip off the front sight base and you now have to find a new barrel.

100-011-235 – Seekins Precision – SP223 Upper Receiver w/Forward Assist

080-001-017WB – Brownells – .223 Wylde HBAR Rifle Gas 20" Barrel

714-000-021 – Precision Reflex, Inc. – Gen III Delta Carbon Fiber Forearm

Shop for AR-15 parts at Brownells.  Go to: ar15podcast.com/parts

Tip:

Things to remember when installing your barrel:

1.  Anti Seizing Grease

2.  Torque Wrench

3.  Barrel Nut Alignment Gauge

4.  Tighten to torque spec several times, then align

Our full show about tools needed for building your AR-15

Main Topic:  Accurizing your AR

1.      Trigger

    • Trigger Job (by Gunsmith)
    • Trigger Replacement

2.      Sling

    • Competition Sling
    • Canvas Sling

3.      Free Float the Barrel

    • Quad Rail
    • Slick Handguard

4.      Paired Bolt and Barrel

5.      Heavy Barrel

6.      Custom Made Barrel

7.      Custom Made Rifle

Feedback:

Chris:  Love the show. Have been listening since day one.  I just wanted to comment about something that was said in regards to eye dominance and shooting an AR. The conventional wisdom is one must always, and only, shoot with ones same eye as trigger finger. However, there are many with eye disease which must shoot in a cross dominant eye manner. To do this there are scope mounts which are so high that they allow you to look through an optic with one’s cross dominant eye. Obviously this will not work with iron sights. Thanks for all the great work.

Arturo:  Reed & Anthony, In ARP #85 you commented on feedback from a listener regarding their recommendation and use of a low mass bolt carrier from Rubber City Armory (RCA). Reed also mentioned he didn't see the need to switch from the standard carrier nor needing to worry about bolt carrier bounce or changing the cyclic timing of the bolt. By the way, in case you didn't know Chris Cerino works/consults with/for RCA.

Though bolt carrier and buffer weight has been used to tune select fire M4/M16's for smoother more reliable operation, the main reason for the low mass bolt carriers you see on the market for AR's today is to reduce felt recoil. They're used a lot by 3 gunners. However, to be effective they need to be used in conjunction with some way of adjusting the amount of gas used to cycle the bolt (typically via an adjustable gas block). What's innovative about Rubber City Armory is that they offer a low mass bolt carrier with an adjustable gas key, so you get a 2 in 1 function. It comes down to simple physics. You reduce and slow down as much as possible the amount of mass that moves rearward when a cartridge fires, and the felt recoil will be less. So you have to both reduce the weight of the bolt carrier and use just enough gas to cycle the action. Basically, enough so that the bolt will hold open on an empty mag after its shot with only 1 round loaded in the mag. The downside of course is that you can only tune for a particular load of ammo. Change the ammo and you'll have to re-adjust the amount of gas going to the bolt. Also, a gas key will be more cumbersome to adjust than a gas block, especially such as one made by Syrac Ordnance.

P.S. Anthony, you get that Tula/Wolf ammo working in your Bushmaster yet?

Adam K: I'm 99 percent sure that Huldra Arms is owned by Jason Adams, owner of Adams Arms. Fyi. Sorry for the presentation. Voice to text while driving.

Kiki: hey guys, love the show...was listening to past shows and came across full auto ar15s....you guys mentioned the lighting link...the lighting link was designed to work with semi auto parts only! no m16 parts! it was specifically designed to work with the colt sp1 bolt....the m16 bolt or newer bolts will not work, due to length of undercut on bottom of bolt, if you look at m16, ar15 and sp1 bolt you'll notice the under side are cut different lengths.....putting a lighting link on any other bolt than sp1 will cause your rifle to fire out of battery...theres youtube videos on this subject....anyways the good thing is that it works, the bad thing is after so many rounds, the link would have to be taken out and flattened back to shape. since its skinny and  soft metal and would bend out of shape and stop working.... hope this helps!

Patrick: Hey Guys, I recently started listening to your podcast after hearing one of you fill in on Gun Guy Radio. I like the show and I'm now looking to buy my first AR.  I'm looking at a Ruger 556E and a S&W M&P15T. I know that they are both different operating systems however they are about the same price at my FFL ($989 AND $919).

My question is…

(1) Which is the better value for the money?

(2) Which do you think a newbie like myself would enjoy more.

Thanks for your reply.

Greg: Reed, I have some feedback about the 5.45 podcast.  It seems as though you had some concern about being "stuck" with an increasingly unavailable round like the 5.45x39 in an AR-15. First, if you already own one, the round is still available in non-corrosive variety. While not as cheap as it was when it was a much more attractive option, it is still as cheap as comparable cartridges.  I own a S&W upper as well as a Ballistic Advantage barreled one (still available barrels).  As far as being stuck with them, should I run out of ammo (no way).  All that is required is a barrel and bolt change. That is no different than changing other calibers. If switching back to 5.56/.223 you could even reuse you flash hider and your gas block.  I can even reuse my 2nd gen. Magpul window mags.  Although I don't see that option in my future as I already have both, it is a valid point to make that you are not stuck with the cost of a whole new upper.  Keep up the podcast. I enjoy listening about the MSR while I work.

Outro: